Radio Thermostat Ct30 Manual

I installed my new CT30 thermostat yesterday. I had a few little glitches and thought that maybe my experience will benefit someone else so here I am. Read the instructions. Dont be the macho 'Oh I know what I am doing' guy because there can be a few tricks.

Jan 20, 2011 How to do a Hard Reset of the 3M50 & CT30. This reset will take the thermostat beck to factory setting. You may want to reset the thermostat. CT30/CT33 Low-voltage Thermostat 3 Label wires and remove old wallplate Use a screwdriver to disconnect wires one by one.As you disconnect each wire.

When I took the unit out of the box the first thing I did was install the batteries to power it up. Since the touch screen becomes active its easy to press and activate features by mistake. I know, I somehow paired the unit accidentally to my hub and had issues right off the bat because I was not ready for that, or trying to do it. Mounting the unit was easy. I have the required 'C' power line and hooking everything up went well.

I even used a small level to make sure it didnt look slanted on the wall. Once mounted its easy to insert the batteries. But since it was already paired I had nothing but trouble trying to get it to work. The solution was to unpair it and start from scratch. I had to use the Exclude feature from the web site development tools (I assume we all know what that is) but it was a little tricky in that once you activate it you have about ten seconds to unpair your device. Clicking Exclude and then running across the house from my desktop to the thermostat was probably not the smartest move, considering that I have a wireles laptop but I didnt think about that until later. After it was successfully unpaired I tried to join it again and it jumped right on the first time.

The new icon appeared in my android app fine as well. Dont be impatient, give the new tile a few moments to sync. It was soon displaying the current temp and everything.

No problems with anything since then, I can turn the fan on and off, set the mode to Cool, Heat or even turn it Off. So far, I am pleased. Dont be impatient, give the new tile a few moments to sync. It was soon displaying the current temp and everything. No problems with anything since then, I think that's very important advice!

I believe when I first paired my Honeywell it looked really weird. Some big number stream on the tile instead of temp. I assumed it was paired wrong and immediately started trying to pick it a part to figure out what was going on. Then a few minutes later looked back at it and everything was fine. Just takes a bit to sync everything up. My CT30 was installed by Comcast as part of their home security + automation system.

I cancelled the service during the trial period, and the tech came back to get the touchscreen controller (= a Comcast-branded Android tablet) and he left all the other hardware. I used the IDE to exclude the CT30 thermostat -- thanks to your writeup -- and then tried to add it to my Smartthings hub. That's where I'm having problems. The Android app detects the new device right away (Other devices' lights up green) and then I waited and waited for 'Join in process.'

It never completes - I waited a few seconds, a few minutes, even an hour. It never completes.

If I interrupt it and click the back button, I have an 'Unknown' tile in the app. I can remove that tile and re-add it a dozen times if I want, following the steps above. I just can't get it to recognize this CT30 Thing. What am I missing?

I'd try these steps: Exclude from the network: - You know the first step, hit exclude in the IDE. - The second step: There is usually a procedure you have to run on the device itself to exclude. It might be as simple as pushing a button or it might be more complex. Check the device manual. If you already know how to do this, ignore me here of course!! Don't want to insult your intelligence but wanted to cover all the bases. Run the procedure to add the device again.

Once you see the part light up green, it has been added. You don't have to wait beyond that. Just hit back now. If it's still showing up as an unknown device, you can try a couple of things: • Wait.

It may be that it just takes a bit for SmartThings to figure out what this device is. • Change the device type in the IDE. Simple Ocr 3 1 Cracking. My Devices ->Click on device in question ->Edit button (at bottom of screen) ->Type: Select Zwave Thermostat ->Update button (at bottom of screen). See if that helps. I hate to wake up an old thread, but I could really use some guidance. I'm setting up Smart Things in a new house we purchased and it has a CT30 put in by Comcast. I tried to link it all weekend, with mixed results - I was able to connect it as a Unknown device.